Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kssulli

Pages: [1]
1
Machine Maintenance / Re: Thread Break Sensor Alarm when in manual mode
« on: December 05, 2016, 06:44:36 PM »
Just a post to state that my quilter is working perfectly with the new manual thread break setting set to 20!  Hooray!

2
Machine Maintenance / Re: Thread Break Sensor Alarm when in manual mode
« on: December 05, 2016, 04:09:20 PM »
I spoke with Gerald in tech support and he advised me to go into setup and up the Manual Thread Break sensor from 10 to 20 and test it out.  He said it can be set as high as 250!!  I will post my results for those of you who may have a problem such as this in the future.

3
Machine Maintenance / Thread Break Sensor Alarm when in manual mode
« on: December 03, 2016, 11:58:28 PM »
I have a Gammill Classic Plus and all of a sudden my thread break sensor is alarming almost every time I go  into manual mode.  Everything is cleaned and oiled and and I've rethreaded the machine.  There is no actual thread break.  Any ideas?

4
Machine Maintenance / Re: Machine Run-Time Clock
« on: April 18, 2016, 01:02:54 PM »
Thank you so much for your timely reply!!

5
Machine Maintenance / Re: Gammill's stand alone bobbin winder
« on: April 17, 2016, 04:34:20 PM »
I saw this post and wondered how you adjust the alignment of the o-ring with the wheel.  There doesn't seem to be a side to side adjustment screw, only a front to back.  Please advise, Shandi.  Thanks!

6
Machine Maintenance / Machine Run-Time Clock
« on: April 17, 2016, 04:17:45 PM »
I like to check the run-time clock on Classic Plus periodically.  This morning I checked it and it said I had 7 hours and 58 minutes of run time.  The last time I made note of the run-time was almost a year ago on the anniversary of the day I bought it and it had 159+ hours on it.  Does anyone know what would cause the clock to reset itself?  Does it turn over automatically at 200 hours?   :-\

Katie

7
Hand Guided Quilting / Re: Problems with Superior Magnifico Thread
« on: November 17, 2015, 09:06:07 PM »
I tested using the Superior Magnifico thread and found that wrapping it around the intermittent tension shaft twice did help my quilter make a proper stitch.  I increased the intermittent tension and it appeared that the thread was still peaking out from between the disks, but the stitch looks good.  I still intend to contact Superior Thread to see if they have any suggestions.  I know that they have given specific advice about their other threads.  Stay posted if interested and I will see if they have anything to say!

8
Hand Guided Quilting / Re: Problems with Superior Magnifico Thread
« on: November 16, 2015, 02:48:28 PM »
I spoke with my long arm technician and he suggested that I wrap the thread twice around the shaft of the intermittent tension device to help hold it in between the disks.  He said many of the very slippery threads may require this.  I will test this out on a test quilt and post my results in case anyone else encounters this issue.

9
Hand Guided Quilting / Problems with Superior Magnifico Thread
« on: November 15, 2015, 04:17:37 PM »
I just started working on a customer quilt using Superior Magnifico Thread.  The thread keeps slipping out of the intermittent tension disks and I'm taking out the quilting for the second time.  Has anyone ever had this issue before and what did you do about it?  I have a 2008 Gammill Classic Plus which has recently been serviced and is on the new Breeze track system.

Pages: [1]